########################################################################### UP-APL01 (UP^2) ########################################################################### Microcode: | Stepping | Version | | -------- | --------------- | | SOC A | N/A | | SOC B | M03506C9_00000032 | | SOC B | M03506CA_0000000C | --------------------------------------------------------------------------- (*) Camera Support Requirement: 1. Windows 10 RS1 2. Driver Install manully 3. BIOS Setting Change (Administrator Mode) CRB Setup -> CRB Chipset -> Uncore Configuration -> IPU Enabled/Disabled : Enabled CRB Setup -> CRB Chipset -> Uncore Configuration -> SA IPU ACPI Mode : IGFX Child Boot -> OS Selection : Windows OV8856 : CRB Setup -> CRB Chipset -> Uncore Configuration -> Rear Camera : IMX135 OV2740 : CRB Setup -> CRB Chipset -> Uncore Configuration -> Front Camera : OV2740 (H/W A1.1 : Only support one kind of camera at the same time) (*) BIOS Flash Rule : Please flash BIOS to [UPA1AM39_FPT] first , then could be flash to [UPA1AM40] or later versions (*) Note : 1. SMBIOS(DMI) Information will be cleared after flash BIOS to [UPA1AM39] 2. FPGA F/W are Different between A1.0 and A1.1 Motherboard ########################################################################### =========================================================================== BIOS Name: [UPA1AM40] (based on [UPA1AM39]) Checksum: [16]MB:[6B83]h Sign-on Message: UP-APL01 R4.0 (UPA1AM40)(08/06/2018) Change: Spec. Changed : Supported Two Setup Options to Control Directions of HAT Pins ; 12 & 35 Fixed : "Quiet Boot" will not be Reload to Default when User Press "F3" in BIOS Setup Menu =========================================================================== =========================================================================== BIOS Name: [UPA1AM39] (based on [UPA1AM38]) Checksum: [16]MB:[513B]h Sign-on Message: UP-APL01 R3.9 (UPA1AM39)(06/29/2018) Change: Fixed : DP/HDMI Flickering under Windows 10 when System is Idling Fixed : User Level Password will be Lost after Re-load BIOS Default =========================================================================== =========================================================================== BIOS Name: [UPA1AM38] (based on [UPA1AM37]) Checksum: [16]MB:[F4FE]h Sign-on Message: UP-APL01 R3.8 (UPA1AM38)(06/20/2018) Change: Spec. Changed : Support Setup Options to Control EXHAT Pin 50/52/54/58/60 Upgrade ApolloLake CPU Microcode =========================================================================== =========================================================================== BIOS Name: [UPA1AM37] (based on [UPA1AM36]) Checksum: [16]MB:[2A7E]h Sign-on Message: UP-APL01 R3.7 (UPA1AM37)(04/18/2018) Change: For H/W A1.1 Changed : birdir_EXHAT12/13/14/15 change from LPSS_I2C5/6 to LPSS_I2C2/3 - Changed for Windows 10 IoT Core & ubiLinux PinCtrol =========================================================================== =========================================================================== BIOS Name: [UPA1AM36] (based on [UPA1AM35]) Checksum: [16]MB:[026D]h Sign-on Message: UP-APL01 R3.6 (UPA1AM36)(04/10/2018) Change: For H/W A1.1 Changed : LPSS_I2C0/I2C1 Mux Function birdir_HAT18/19/20/21 change from ISH_GPIO13/12/11/10 to SIO_SPI_2_FS0/SIO_SPI_2_CLK/SDIO_CLK/AVS_I2S2_MCLK For H/W A1.1 Changed : birdir_EXHAT12/13/14/15 change from LPSS_I2C5/6 to LPSS_I2C2/3 Spec. Change : Request from Intel , HAT PIN 12/35 Default as Output Direction for I2S Function Spec. Change : Request from Intel , Change aDSP Key from cAvsImage1Manifest to cAvsImage0Manifest Remove Intel ISS Debug/Trace Support for Formal Release Version Note: SMBIOS(DMI) Information will be cleared after flash BIOS to this version =========================================================================== =========================================================================== BIOS Name: [UPA1AM35] (based on [UPA1AM34]) Checksum: [16]MB:[1BE6]h Sign-on Message: UP-APL01 R3.5 (UPA1AM35)(02/13/2018) Change: Power Consumption will be Decreased less than 1 second =========================================================================== =========================================================================== BIOS Name: [UPA1AM34] (based on [UPA1AM33]) Checksum: [16]MB:[418A]h Sign-on Message: UP-APL01 R3.4 (UPA1AM34)(01/19/2018) Change: 1. PM Request : CPU Power Limit to 13W 2. Support Android-IA 3. For H/W A1.1 Changed : Emutex Request - SMBIOS Base Board Version will be "V0.5" on H/W A1.1 Board 4. For H/W A1.1 Changed : MIPI Camera Design Changed 5. For Intel Security Advisory - Update CPU Microcode =========================================================================== =========================================================================== BIOS Name: [UPA1AM33] (based on [UPA1AM32]) Checksum: [16]MB:[1749]h Sign-on Message: UP-APL01 R3.3 (UPA1AM33)(01/17/2018) Change: 1. Spec. Changed - BIOS Logo Change =========================================================================== =========================================================================== BIOS Name: [UPA1AM32.bin] (based on [UPA1AM31]) Checksum: [16]MB:[35CB]h Sign-on Message: UP-APL01 R3.2 (UPA1AM32)(12/14/2017) Change: 1. Fixed : USB 3.0 key will run lower speed after updating TXE ver.3.1.50.2222 =========================================================================== =========================================================================== BIOS Name: [UPA1AM31.bin] (based on [UPA1AM30]) Checksum: [16]MB:[9C3F]h Sign-on Message: UP-APL01 R3.1 (UPA1AM31)(12/12/2017) Change: 1. Intel Request : Support Apollo Lake DCI Debug Interface Note: 1. SMBIOS Information will be lost after flash to this version . =========================================================================== =========================================================================== BIOS Name: [UPA1AM30.bin] (based on [UPA1AM23]) Checksum: [16]MB:[86DB]h Sign-on Message: UP-APL01 R3.0 (UPA1AM30)(12/07/2017) Change: 1. Fix issue that after disabling setup item LPSS SPI#1, SPI#3 will disappear too. 2. Fix issue that resource Hub proxy 4 contains I2C0 and I2C1 controller, once either one is disabled then the other one will not work (ProblemCode:51 in OS DM). 3. Disable other funxtion under same device when function 0 is disabled on first boot for SPI, UART and I2C. 4. Fixed : Intel ME/TXE Security Issue 5. Update Apollo Lake Intel PMC FW v03.1d.00 Release 6. Emutex's Request : Support Setup Option Control for SPI ADC124S101 Channel 0 ~ 3 7. Workaround : HDMI / Display Port will flickering with non-recommend resoulution under Windows 10 Note: 1. SMBIOS Information will be lost after flash to this version . =========================================================================== =========================================================================== BIOS Name: [UPA1AM23.bin] (based on [UPA1AM22]) Checksum: [16]MB:[E407]h Sign-on Message: UP-APL01 R2.3 (UPA1AM23)(11/17/2017) Change: FOR Win10 IoT Core : Support WIN10 IoT core UWP (Universal Windows Platform). Resource Hub proxy will present only when setup OS Selection is Win10 IOT Core. Known Issue: 1. After disabling setup item "LPSS SPI#1", SPI#3 will disappear too. 2. Resource Hub proxy 4 contains I2C0 and I2C1 controller, once either one is disabled then the other one will not work (ProblemCode:51 in OS DM). 3. MSFT GpioTestTool.exe will get all the 54 pins in resource Hub proxy in order. User will confuse with HAT GPIO pin number, because we are now transferring the pin number in our OS APP. =========================================================================== =========================================================================== BIOS Name: [UPA1AM22.bin] (based on [UPA1AM21]) Checksum: [16]MB:[6DBF]h Sign-on Message: UP-APL01 R2.2 (UPA1AM22)(10/11/2017) Change: Fixed : Blink Display under Windows with E0 Stepping CPU =========================================================================== =========================================================================== BIOS Name: [UPA1AM21.bin] (based on [UPA1AM20]) Checksum: [16]MB:[1078]h Sign-on Message: UP-APL01 R2.1 (UPA1AM21)(09/01/2017) Change: Emutex Request : [LPSS I2C #2 Speed] default as [Standard Mode] =========================================================================== =========================================================================== BIOS Name: [UPA1AM20.bin] (based on [UPA1AM19]) Checksum: [16]MB:[1CCA]h Sign-on Message: UP-APL01 R2.0 (UPA1AM20)(08/11/2017) Change: FOR Win10 IoT Core : Support Secure Boot and Disabled as default. Fixed : Custom SMBIOS Information will be gone after CMOS Battery lossed Fixed : Default Administrator Password will be gone after BIOS Restore Default Emutex Request : USB OTG Enabled as Default, and Override Related Register Settings =========================================================================== =========================================================================== BIOS Name: [UPA1AM191.bin] (based on [UPA1AM19]) Checksum: [16]MB:[9B56]h Sign-on Message: UP-APL01 R1.9.1 (UPA1AM19)(07/27/2017) Change: Supported fTPM - Intel PTT Note: Only for AAEON Internal =========================================================================== =========================================================================== BIOS Name: [UPA1AM19.bin] (based on [UPA1AM18]) Checksum: [16]MB:[3B2A]h Sign-on Message: UP-APL01 R1.9 (UPA1AM19)(07/05/2017) Change: Custom Request : Dynamic Hide a virtual Emutex's ASL Device under Windows, depend on "OS Selection" under Setup Menu Fixed : CPU Frequency Incorrect when EIST Disabled =========================================================================== =========================================================================== BIOS Name: [UPA1AM18.bin] (based on [UPA1AM17]) Checksum: [16]MB:[7E78]h Sign-on Message: UP-APL01 R1.8 (UPA1AM18)(06/23/2017) Change: Fixed : Incorrect EN_I2C0 / EN_I2C1 command setting Emutex's Request : According to I2C Function Enabled/Disabled, corresponding pins should be Hi-Z Support MIPI CSI Camera : OV2740 & OV8856 Camera Support Requirement: 1. Windows 10 RS1 2. Driver Install manully 3. BIOS Setting Change (Administrator Mode) CRB Setup -> CRB Chipset -> Uncore Configuration -> IPU Enabled/Disabled : Enabled CRB Setup -> CRB Chipset -> Uncore Configuration -> SA IPU ACPI Mode : IGFX Child Boot -> OS Selection : Windows Only support one kind of camera at the same time OV8856 : CRB Setup -> CRB Chipset -> Uncore Configuration -> Rear Camera : IMX135 OV2740 : CRB Setup -> CRB Chipset -> Uncore Configuration -> Front Camera : OV2740 =========================================================================== =========================================================================== BIOS Name: [UPA1AM17.bin] (based on [UPA1AM16]) Checksum: [16]MB:[B73D]h Sign-on Message: UP-APL01 R1.7 (UPA1AM17)(06/14/2017) Change: Emutex's Request : Re-arrange BIOS Setup Menu and BIOS Default Modification Emutex's Request : aDSP pubkey only supported cAvsImage1Manifest Fixed : Wrong Setup String of Memory Type =========================================================================== =========================================================================== BIOS Name: [UPA1AM16.bin] (based on [UPA1AM15]) Checksum: [16]MB:[DFD3]h Sign-on Message: UP-APL01 R1.6 (UPA1AM16)(06/07/2017) Change: Emutex's Request : USB Device as the 1st boot priority boot device. Emutex's Request : All GPIOs as GPIO Drive Mode even it's multi-function pin, and default as MultiFunctions Emutex's Request : Built in a custom aDSP public key Emutex's Request : Re-arrange BIOS Setup Menu =========================================================================== =========================================================================== BIOS Name: [UPA1AM15.bin] (based on [UPA1AM14]) Checksum: [16]MB:[133F]h Sign-on Message: UP-APL01 R1.5 (UPA1AM15)(05/26/2017) Change: Emutex's Request : Support FPGA initialization during BIOS POST Emutex's Request : Fixed GPIO Interrupt Issue =========================================================================== =========================================================================== BIOS Name: [UPA1AM14.bin] (based on [UPA1AM13]) Checksum: [16]MB:[76B9]h Sign-on Message: UP-APL01 R1.4 (UPA1AM14)(05/09/2017) Change: Emutex's Request : All GPIO Input Pins as "GPIO Driver Mode" =========================================================================== =========================================================================== BIOS Name: [UPA1AM13.bin] (based on [UPA1AM12]) Checksum: [16]MB:[1DE1]h Sign-on Message: UP-APL01 R1.3 (UPA1AM13)(04/24/2017) Change: Customer's Request (Emutex) : "Console Redirection" : Enabled =========================================================================== =========================================================================== BIOS Name: [UPA1AM12.bin] (based on [UPA1AM11]) Checksum: [16]MB:[61FF]h Sign-on Message: UP-APL01 R1.2 (UPA1AM12)(04/24/2017) Change: Customer's Request (Emutex) : "VT-d" : Enabled Customer's Request (Emutex) : "OS Selection" : Intel Linux =========================================================================== =========================================================================== BIOS Name: [UPA1AM11.bin] (based on [UPA1AM10]) Checksum: [16]MB:[1968]h Sign-on Message: UP-APL01 R1.1 (UPA1AM11)(04/21/2017) Change: Customer's Request (Emutex) : Emutex released a new ACPI table for bug fixed =========================================================================== =========================================================================== BIOS Name: [UPA1AM10.bin] (based on [UPA1AM09]) Checksum: [16]MB:[4F7D]h Sign-on Message: UP-APL01 R1.0 (UPA1AM10)(04/20/2017) Change: Customer's Request (Emutex) : Supported BIOS Default Password Customer's Request (Emutex) : Re-arrange BIOS Setup Menu Customer's Request (Emutex) : Built in a ACPI Table for HAT Function =========================================================================== =========================================================================== BIOS Name: [UPA1AM09.bin] (based on [UPA1AM08]) Checksum: [16]MB:[95B8]h Sign-on Message: UP-APL01 R0.9 (UPA1AM09)(04/17/2017) Change: Customer's Request (Emutex) : SMBIOS TYPE 2 - BASE BOARD "BASE_BOARD_VERSION" as V0.3 Customer's Request (Emutex) : Expand Main BIOS Size for reserved. =========================================================================== =========================================================================== BIOS Name: [UPA1AM08.bin] (based on [UPA1AM07]) Checksum: [16]MB:[880F]h Sign-on Message: UP-APL01 R0.8 (UPA1AM08)(04/12/2017) Change: FOR UP^2, Support Setup Items to Control HAT 40 Pins. =========================================================================== =========================================================================== BIOS Name: [UPA1AM07.bin] (based on [UPA1AM06]) Checksum: [16]MB:[668F]h Sign-on Message: UP-APL01 R0.7 (UPA1AM07)(03/22/2017) Change: H/W Design: FOR UP-APL01, FAN from PWM2 only supported On or Off H/W Design Changed: Support PCIe / mSATA Switch by GPIO Pin PM Product Spec. Requirement: FOR UP-APL01, Support Power Button Notify from Wake State PM Product Spec. Requirement: FOR UP-APL01, Support USB wake from S3 & S4. Upgrade to the latest AAEON CRB Code =========================================================================== =========================================================================== BIOS Name: [UPA1AM06.bin] (based on [UPA1AM05]) Checksum: [16]MB:[5688]h Sign-on Message: UP-APL01 R0.6 (UPA1AM06)(02/21/2017) Change: Support Uefi PXE boot (Network Stack) Support USB ports ejectable feature Support Console Redirection feature (HSUART0 only) =========================================================================== =========================================================================== BIOS Name: [UPA1AM05.bin] (based on [UPA1AM04]) Checksum: [16]MB:[E329]h Sign-on Message: UP-APL01 R0.5 (UPA1AM05)(02/10/2017) Change: FOR H/W A0.3 design changed, re-define SoC GPIO multifunction pins FOR FAN default enabled, PWM0 / PWM1 / PWM2 / PWM3 default as GPO High "GPIO_37 PWM3" was not floating anymore Support CPU DTS temperature Arrange BIOS setup Fixed: There's a yellow mark under windows(SD Controller) H/W A0.3 Changed, DDI0 changed from HDMI to DP Built in LPSS Device ASL code Only support 1 LPSS UART Remove unnecessary ASL devices Core Base Upgrade =========================================================================== =========================================================================== BIOS Name: [UPA1AM04.bin] (based on [UPA1AM03]) Checksum: [16]MB:[8AE3]h Sign-on Message: UP-APL01 R0.4 (UPA1AM04)(01/03/2017) Change: Fine-tuned, Integrated Graphics Power will not be dropped when running Intel TAT Gfx workload Adjust SATA Port 0 TX Voltage Swing according to SI's test result. Upgrade to the latest AAEON CRB Code =========================================================================== =========================================================================== BIOS Name: [UPA1AM03.bin] (based on [UPA1AM02]) Checksum: [16]MB:[BE6B]h Sign-on Message: UP-APL01 R0.3 (UPA1AM03)(12/08/2016) Changes: FOR Apollolake Platform, support GPIO Power Button SCI FOR UP-APL01, CPU Frequency Should be Capable to Reach to the Maximum Correct SMBIOS Data Support OnBoard Flash BIOS under EFI Shell =========================================================================== =========================================================================== BIOS Name: [UPA1AM02.bin] (based on [UPA1AM01]) Checksum: [16]MB:[B613]h Sign-on Message: R0.2 (UPA1AM02)(12/02/2016) Changes: BIOS Default Modification. Cont. BIOS Default Modification PCIe Ports CLKREQs Routing =========================================================================== =========================================================================== BIOS Name: [UPA1AM01.bin] (based on [UPA1AM00]) Checksum: [16]MB:[9F52]h Sign-on Message: R0.1 (UPA1AM01)(11/29/2016) Changes: PCIe Ports CLKREQs Routing FOR UP-APL01, VBIOS Porting in Project Level H/W Design Changed from 8MB to 16MB FOR UP-APL01, SoC GPIO MultiFunction Pins Porting TXE Configuration =========================================================================== =========================================================================== BIOS Name: [UPA1AM00.bin] (based on [1ATJS024_M0B]) Checksum: [8]MB:[D0C2]h Sign-on Message: R0.0 (UPA1AM00)(11/24/2016) Changes: Support Memory Down on UP-APL01, cont. (for UP-APL01 4GB memory down, 1GB x 4) FOR UP-APL01, support more than 1 memory down configurations Migrate SoC GPIO Pins Configurations to Project Level Power Solution : PMIC for UP-APL01 Override BOARDID for UP-APL01, and FLASH SIZE as 8MB temporarily Support Memory Down on UP-APL01, override SMIP F/W ===========================================================================